INNE EBOOKI AUTORA
-20%
Praca zbiorowa
Wydawca:
Format:
pdf, ibuk
The paper deals with analysis of chip formation and related aspects of the chip formation as chip thickness, chip thickness ratio, shear angle and chip segmentation during turning hardened steel 100Cr6. The paper draws a comparison of some aspects of the chip formation between turning roll bearing steel in the annealed and turning roll bearing steel in the hardened state. The results of the analysis show that there is the formation of a segmented chip in the case of hard turning. This process of the chip formation significantly affects all parameters related to the plastic deformation in the cutting zone. Moreover, the formation of the segmented chip causes the instability of a cutting process, the high intensity of tool wear and the generation a lot of heat in the cutting zone. That heat causes generation of a high temperature in the cutting zone (the thermal load of a cutting tool).
Rok wydania | 2008 |
---|---|
Liczba stron | 150 |
Kategoria | Materiałoznawstwo |
Wydawca | Wydawnictwo Politechniki Poznańskiej |
Numer wydania | 1 |
Język publikacji | polski |
Informacja o sprzedawcy | ePWN sp. z o.o. |
INNE EBOOKI AUTORA
POLECAMY
Ciekawe propozycje
Spis treści
NOTKI BIOGRAFICZNE | 5 |
Profesor Andrzej Barbacki | 5 |
Profesor Czesław Cempel | 6 |
Profesor Jerzy Kozak | 7 |
Profesor Krzysztof Marchelek | 8 |
Profesor Ryszard Rohatyński | 9 |
Profesor Jan Szadkowski | 10 |
Profesor Michał Szweycer | 11 |
Profesor Krzysztof Tubielewicz | 12 |
OBRÓBKA SKRAWANIEM (WIÓROWA I ŚCIERNA) | 13 |
1. Miroslav Neslušan, Róbert Čep – Aspects of chip formation during turning of hardened steel 100Cr6 | 13 |
Niektóre aspekty tworzenia wióra podczas obróbki skrawaniem hartowanej stali 100Cr6 | 23 |
POMIARY I KONTROLA | 25 |
2. Jacek Michalski – Analiza częstotliwościowa topografii gładzonej powierzchni tulei cylindrowych | 25 |
Spectral analysis topography of cylinder liner honed surface | 34 |
PROJEKTOWANIE ORAZ AUTOMATYZACJA PROCESÓW I MASZYN TECHNOLOGICZNYCH | 35 |
3. Marcin Chciuk, Adam Myszkowski – Wykorzystanie trzyosiowego dżojstika dotykowego z cieczą magnetoreologiczną i siłowym sprzężeniem zwrotnym do sterowania ramionami robota | 35 |
Using three-axial haptic joystick with magnetorheological fluid and force feedback for control robot’s arm | 42 |
4. Milena Kušnerová, Jan Valíček, Sergej Hloch, Marek Sadílek, Robert Čep – Hydrodynamic resonation through-flow system as acoustic circuit | 43 |
Rezonans hydrodynamiczny z wykorzystaniem systemu przepływowego jako obwodu akustycznego | 52 |
5. Andrzej Milecki – Simulation investigations of electrohydraulic drive controlled by haptic joystick | 53 |
Badania symulacyjne napędu elektrohydraulicznego sterowanego dżojstikiem z siłowym sprzężeniem zwrotnym | 61 |
6. Katarína Monková, Peter Monka – The coding of manufacturing system objects inside the new software application | 63 |
Kodowanie obiektów systemu wytwarzania z wykorzystaniem nowej aplikacji | 70 |
7. Jana Novakova, Robert Čep, Stanisław Legutko – Creative formation of products in mechanical engineering | 71 |
Twórcze kształtowanie produktów w inżynierii mechanicznej | 78 |
8. Dariusz Sędziak, Marcin Pelic – Modelowanie serwozaworu z piezoelementem belkowym w stopniu sterującym i z elektrycznym sprzężeniem zwrotnym | 79 |
The modeling of electrohydraulic servovalve with piezobender and electronic feedback | 88 |
9. Jerzy Stojek – Wykorzystanie techniki CFD do modelowania zjawisk przepływowych w hydraulicznych zaworach wzniosowych | 89 |
Application of CFD for modeling flow-related effects in the hydraulic lift valve | 97 |
MONTAŻ MASZYN I URZĄDZEŃ | 99 |
10. Olaf Ciszak, Jan Żurek – Badanie wydajności gniazda montażu wrzeciennika głównego centrum tokarskiego | 99 |
Productive study of the lathe cente spindle assembly process | 105 |
11. Marcin Suszyński, Olaf Ciszak, Jan Żurek – Modelowanie montażowej struktury wyrobu za pomocą hipergrafu i grafu skierowanego oraz ustalanie dopuszczalnej kolejności montażu | 107 |
Modeling of the assembly structure with using directed graph and hypergraph and defining of the possible assembly sequence | 116 |
EKSPLOATACJA MASZYN I URZĄDZEŃ ECHNOLOGICZNYCH | 117 |
12. Paweł Gutowski, Mariusz Leus – Analiza wpływu drgań kontaktowych stycznych wzdłużnych na siłę tarcia | 117 |
The analysis of longitudinal tangential contact vibration effect on friction force | 126 |
13. Zbigniew Nowakowski, Krzysztof Ślimak – Wpływ stanu połączenia narzędzia z wrzecionem obrabiarki na strukturę geometryczną powierzchni obrobionej | 127 |
Influence of tool with machine tool spindle interface condition on geometrical structure of machined surface | 135 |
14. Ryszard Wójcik – Nowe media i sposoby ich doprowadzania do strefy szlifowania | 137 |
Application of new kinds of cooling media and supplying methods during surface grinding | 145 |
WSPOMNIENIA POŚMIERTNE | 147 |
Prof. dr hab. inż. Ryszard Grajdek | 147 |
Prof. zw. dr hab. inż. dr h.c. Jerzy Gronostajski | 148 |
Prof. zw. dr hab. inż. dr h.c. Jan Harasymowicz | 149 |